Skip Navigation 
NOAA logo - Click to go to the NOAA homepage National Weather Service   NWS logo - Click to go to the NWS homepage
Ohio River Forecast Center
Local weather forecast by
"City, ST" is the U.S. government's official web portal to all federal, state and local government web resources and services.

What Data Do We Get?


River Stages

River stages are our most important type of data. River stage data is collected in one of three ways:

1. Gage Houses

Gage houses are the most common sources of river stage data. Here is a diagram of a typical gage house:

diagram of a gage house

A gage house consists of a well dug along the riverbank with an instrument house above it. Water enters the well through one or more inlet pipes. The water in the well will be at the same level as the river, so the recording equipment above it actually records the water level in the well. This data can be either saved at the gage site and queried by telephone, or can be transmitted via satellite or radio.

2. Wire Weight Gage

This type of gage is usually mounted to the side of a bridge. It consists of a spool of wire, with a weight attached to the end of the wire. The river level is measured by lowering the weight until it touches the river surface. The distance between the bridge and the water is measured, which is then subtracted from the distace from the bridge to the riverbed. The resulting number is the river stage.

3. Staff Gage

The third type of gage is by far the simplest. A staff gage is basically a ruler attached to the river bank, a bridge piling or anything next to the river. The river level is measured by reading the markings on the gage.

Rainfall Data

Rainfall amounts are also necessary for river forecasting, since, without rainfall data, one cannot predict runoff, and therefore, future stages. There are three general types of rain gages, plus another unusual tool for measuring rainfall.

1. Weighing Gage

This type of gage consists of an antifreeze-filled collection bucket mounted on top of a scale. As rain, snow, hail, or any type of precipitation falls into the collecting bucket, the bucket becomes heavier. The antifreeze is there to allow the liquid content for frozen precipitation to be measured. Every few minutes, a recorder attached to the scale records the weight of the bucket contents. Since the size of the bucket, the weight of antifreeze, and the density of water are known, a precipitation amount can be measured from the weight of the bucket.

2. Tipping Bucket

A tipping bucket rain gage consists of a funnel and a rocker mechanism with two little "buckets" on it, located underneath the funnel. When rain falls into the funnel, with fills one of the little buckets on the rocker mechanism. Once a given amount of rain falls into the funnel, usually 0.01 inches, the rocker "tips" over, emptying one of the buckets and moving the other one underneath the funnel. A recorder in the gage records each tip and the time it occurred. The tipping bucket gage has its disadvantages, however. It cannot be used in freezing weather because the mechanism or the funnel hole can freeze solid. Sometimes the tipper mechanism doesn't work or double tips.

3. Standard Rain Gage

A standard rain gage consists of only three parts, a funnel, a can, and a measuring tube. Rain fall into the funnel and into the measuring tube. Since the funnel is wider than the measuring tube, the depth of water in the measuring tube would be greater than if the tube was as wide as the funnel. This allows rainfall to be measured to the nearest 0.01 inch. When frozen precipitation is expected, the funnel and measuring tube are removed, and the precipitation is collected in the can. To measure the liquid equivalent of the frozen precipitation, the contents of the can are melted and poured into the measuring tube to be measured.

4. Doppler Radar

That's right, it says Doppler radar. One of the functions of the new Doppler radar is estimating one, three, and storm total rainfall amounts based on the intensity of the radar echoes. A program is being tested to take the radar-derived rainfall amounts and combine this data with rain gage data and show the resulting rainfall estimations on a map.

Temperature and Sunshine Data

Temperature and sunshine data are useful with both snowmelt and evaporation estimations used in our river model. Hourly temperature data comes from official NWS observing sites, usually at airports. Some of these airports also report total minutes of sunshine observed in the previous day. Volunteer NWS cooperative observers also report the previous day's maximum and minimum temperature.

Next: how we get the data we receive.

Monday, November 17, 2003
National Weather Service
Ohio River Forecast Center
1901 South State Route 134
Wilmington, OH 45177-9708
Page last modified: Wednesday, June 19, 2013 11:32 AM
Information Quality
Privacy Policy
Freedom of Information Act (FOIA)
About Us
Career Opportunities